Solid-state TPV converts solar thermal to utility-scale electricity

27th July 2016
Posted By : Enaie Azambuja
Solid-state TPV converts solar thermal to utility-scale electricity

Solid-state thermophotovoltaics (TPV) could provide a high-efficiency alternative for directly converting high-temperature heat from concentrated solar thermal to utility-scale electricity. New computer modeling suggests that high temperature TPV conversion - which captures infrared radiation from very hot surfaces - could one day rival combined-cycle turbine systems when combined with thermal storage using liquid metal at temperatures around 1,300ºC.

Advances in high-temperature components and improved system modeling, combined with the potential for conversion costs an order of magnitude lower than those of turbines, suggest that TPV could offer a pathway for efficiently storing and producing electrical power from solar thermal sources, a new study suggests.

The underlying technologies of high temperature storage and thermophotovoltaic conversion could also be used to produce grid-scale batteries able to rapidly supplement other power sources by storing heat for quick conversion to electricity.

The research, supported by ARPA-E, was reported in the journal Energy & Environmental Science by researchers at the Georgia Institute of Technology.

"The goal for our study was to provide a heat transfer and thermodynamic perspective on a system that combines concentrated solar power (CSP) with thermal storage and TPV to show that such a system is worthy of renewed attention," said Asegun Henry, an assistant professor in the George W. Woodruff School of Mechanical Engineering at Georgia Tech.

"In the context of the full system, we suggest that the efficiency could one day rival the best heat engines available on planet today."

TPV operates on the same principle as solar cells in wide use today, but converts photons at infrared wavelengths rather than those in the visible spectrum. Infrared is the predominant kind of heat and light emitted by heaters that glow red-hot.

Most research reported in the energy literature suggests that the conversion rate of TPV would be less than 20%, not competitive with other heat engines. But Henry believes those calculations do not properly consider the conversion wavelengths or account for efficiencies possible when the full heat delivery system is considered.

"The entire system could be quite efficient if we understand where the heat is flowing and design appropriately," Henry said. "We believe there is a pathway to make these TPV cells an order of magnitude cheaper than turbines for converting thermal energy to electricity."

The heat would be supplied by a CSP system collecting the sun's thermal energy using reflectors. The heat would be used to melt silicon, which could be stored in large insulated reservoirs until needed; the heat would then be released as the silicon solidifies.

By moving the TPV cells when their power isn't needed, the system could be rapidly switched on and off to supplement electricity from wind or direct solar PV sources, Henry said.

"It's the dream of utility companies to have a resource that could go from zero to full power in a matter of seconds," he said. "With the right insulation and shading of the cells, we could switch them on and off faster than any other conversion technology."

The critical challenge to making renewable energy competitive with fossil fuels at the utility scale is making the electricity dispatchable.

The cost advantages of thermal storage over electrochemical storage also make a TPV with thermal energy storage (TES) system attractive for converting and storing energy for use on the grid, said Hamid Reza Seyf, a graduate research assistant who did the system modeling.

This schematic shows a thermophotovoltaic system that would be used to convert high-temperature heat from concentrated solar thermal to utility-scale electricity. Credit: Hamid Reza Seyf

"We are combining the great economic advantages of TES with the potential for low cost and high performance derived from TPV cells fabricated on reusable substrates, with high reflectivity back reflectors for photon recycling," he said.

"If solar energy is produced and not needed, you could use it to produce thermal energy that could be stored and discharged to TPV power block when needed. The extremely long lifetimes, high round-trip efficiency, and low cost of the thermal storage compared to electrochemical batteries make the TES very attractive."

If the TPV power block could be made 60% efficient, it could compete with most cost effective and efficient heat engine that has ever been achieved commercially, which is accomplished through a tandem turbine based cycle. The cost of turbines is well established and unlikely to see significant decrease, hence the only way to reduce their cost is by increasing their efficiency.

However, because current turbines are extremely efficient and operate near their thermodynamic limit, there is little room for efficiency enhancement. TPV power block not only has the potential for lowering the cost but also has much more room for efficiency improvement, Seyf said.

The computational model shows that a TPV system coupled with concentrated solar and storage could be as much as 65% efficient. But attaining that would require a long-term research initiative.

In their model, the group studied the effects of a silver-based back surface reflector (BSR) to bounce unused light back to the emitter. The study quantified the importance of the BSR reflectivity to the overall system performance.

Henry's research group has recently demonstrated pumps, storage containers and other components that can operate at extreme temperatures of 1,300ºC and above.

The researchers hope their new paper encourages others to pursue TPV improvements - including fabrication of TPV cells on reusable substrates - that could lead to development of real-world systems at costs competitive with fossil fuels.

You must be logged in to comment

Write a comment

No comments

Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

Mobile World Congress 2018
26th February 2018
Spain Barcelona
embedded world 2018
27th February 2018
Germany Nuremberg
Industry 4.0 Summit 2018
28th February 2018
United Kingdom Manchester
Factories of the Future Expo 2018
28th February 2018
United Kingdom Manchester
Power supply design seminar 2018
1st March 2018
United Kingdom