Light-trapping 3D solar cells undergo space testing

19th July 2016
Posted By : Enaie Azambuja
Light-trapping 3D solar cells undergo space testing

A novel 3D solar cell design developed at Georgia Tech will soon get its first testing in space aboard the International Space Station. An experimental module containing 18 test cells was launched to the ISS, and will be installed on the exterior of the station to study the cells’ performance and their ability to withstand the rigors of space. In addition to testing the 3D format, the module will also study a low-cost copper-zinc-tin-sulfide (CZTS) solar cell formulation.

In all, the module launched to the ISS contains four types of PV devices: 3D cells based on conventional cadmium telluride, 3D cells based on CZTS materials, traditional planar solar cells produced at Georgia Tech, and planar cells based on CZTS.

The experiment was aboard SpaceX's Falcon 9 rocket that blasted off at 12:45 a.m. EDT from Cape Canaveral Air Force Station in Florida.

“We want to see both the light-trapping performance of our 3D solar cells and how they are going to respond to the harshness of space,” said Jud Ready, a principal research engineer at the Georgia Tech Research Institute (GTRI) and an adjunct professor in the Georgia Tech School of Materials Science and Engineering.

“We will also measure performance against temperature, because temperature has an influence on the performance of a solar cell.”

Built by coating miniature carbon nanotube “towers” with a photo-absorber that captures sunlight from all angles, the 3D cells developed by Ready’s lab could boost the amount of power obtained from the small surface areas many spacecraft have. The cells would absorb light from any direction, eliminating the need for mechanical devices to aim PV modules toward the sun.

The PV cell experiment will be installed on the NanoRacks External Platform (NREP), where robustness of the solar cells will be studied under harsh space conditions for six months.

The project is sponsored by the Center for the Advancement of Science in Space (CASIS), and the Space Station opportunity was provided by NanoRacks via its Space Act Agreement with NASA’s U.S. National Labs.

"The CZTS photovoltaic arrays were built using the readily available elements copper, zinc, tin and sulfur to replace rarer CIGS – copper, indium, gallium and selenium – which are used in similar thin-film solar cells," said Ready.

"The CZTS approach produces an efficient photo-absorber using earth-abundant materials that cost around a thousand times less than rare-earth elements like indium, gallium and selenium."

One virtue of CZTS photovoltaic material is its electron band structure, Ready explained. Like CIGS, CZTS is a direct band gap material. In semiconductor physics, this means incoming solar photons are able to emit current-producing electrons directly, rather than moving through power-robbing intermediate states as indirect band gap materials, like silicon, require.

Moreover, Ready said, direct band gap materials have good resistance to the powerful ionising radiation encountered in space. That's because direct band gaps are larger than indirect band gaps; it's harder for radiation to damage these larger gaps so severely that functionality is seriously impaired.

The 3D capability could prove especially valuable on the International Space Station, which is exposed daily to 15-16 sunrises and sunsets as it orbits Earth every 92 minutes at 17,150 m.p.h. The 3D towers can exploit the sun's rays for longer periods than conventional 2D planar – or flat – designs, which work most efficiently only when the sun is directly overhead.

"With our 3D design, as the sun's angle increases more surface is exposed and there's a growing chance that photons will enter," Ready said. "Also, 3D technology provides more opportunity for photons to bounce around between the towers, increasing the likelihood they will be converted to electron hole pairs and produce mobile charge carriers."

As the ISS orbits, the 3D arrays' performance will be compared to a high quality commercial 2D planar cell array installed nearby. If things go as expected, GTRI's cells will provide relatively better performance than the other cells as they move away from high noon. The new CZTS 3D arrays will also be tested in space against an older 3D design made by GTRI using cadmium telluride.

One of the GTRI development team’s key achievements to date has been identifying the best ways to manufacture CZTS solar cells. The team has pinpointed techniques for successfully processing the four Earth-abundant elements into an efficient photo absorber.

"In manufacturing you have to heat these elements, and one major issue is that they evaporate at different rates," Ready explained. "Getting them to blend in the desired ratios, so that the stoichiometry is retained and electron levels of the constituent elements match up as they should, has been a challenge."

GTRI's photovoltaic arrays will be encased in Lexan containers aboard the ISS. Lexan, a clear yet strong polymer, produces minimal interference with incoming solar rays but can protect the delicate arrays from astronauts and space debris – and also protect the crew from any pieces of the arrays that might separate.

After the six-month mission, the solar cells will be sent back to Earth via a cargo ship. The research team will assess the cells’ post-mission performance and look for damage from radiation and other space hazards.

"If it can survive in space, which is the harshest of environments from the standpoint of wide temperature swings, radiation and numerous other factors, then we can be confident it will work well down on Earth," Ready said.

Ready’s novel 3D photovoltaic technology (U.S. Patent # 8,350,146) is licensed for commercial manufacture by Bloo Solar of El Dorado Hills, CA.

You must be logged in to comment

Write a comment

No comments

Sign up to view our publications

Sign up

Sign up to view our downloads

Sign up

Mobile World Congress 2018
26th February 2018
Spain Barcelona
embedded world 2018
27th February 2018
Germany Nuremberg
Industry 4.0 Summit 2018
28th February 2018
United Kingdom Manchester
Factories of the Future Expo 2018
28th February 2018
United Kingdom Manchester
Power supply design seminar 2018
1st March 2018
United Kingdom